Fluke                                                       MET/CAL Procedure
=============================================================================
INSTRUMENT:            Angus Electric POWER MASTER IIIB: (1 yr) CAL VER /5500
DATE:                  26-Aug-97
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 1.5 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       9
NUMBER OF LINES:       106
CONFIGURATION:         Fluke 5500A
STANDARD:              Fluke 5500A/COIL
=============================================================================
#
# Compatibility:
#   5500/CAL 4.0 or MET/CAL 4.0 or later.
#
# Subprocedures:
#   None
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5500A accuracy file contains 90 day specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  STD          Fluke 5500A/COIL
  1.002  ASK-                        P                            F        V
  1.003  ASK+           K                              X
  1.004  HEAD         PRELIMINARY INSTRUCTIONS
  1.005  DISP         Turn UUT power switch to ON.
  1.005  DISP
  1.005  DISP         Warm-up time: NONE
  1.005  DISP         Temperature: 23 +/-3 degC
  1.005  DISP         Humidity: 55 +/-10%
  1.006  DISP         [32]                WARNING
  1.006  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.006  DISP         of this calibration.  DEATH ON CONTACT may result if
  1.006  DISP         personnel fail to observe safety precautions.
  1.007  HEAD         {AC VOLTAGE}
  1.008  DISP         Connect the 5500A and the UUT as follows:
  1.008  DISP         [32] 5500A NORMAL HI to UUT Red Voltage Input
  1.008  DISP         [32] 5500A NORMAL LO to UUT White Voltage Input
  1.009  DISP         Set Function to Volts
  1.009  DISP         Set Element to RD
  1.009  DISP         Set Monitor to Center
  1.009  DISP         Set Mode to Run
  1.010  5500         60.0V          1% 0.1U       60H            SI       2W
  2.001  5500         600V           1% 1U         60H            SI       2W
  3.001  HEAD         {AC CURRENT}
  3.002  DISP         Disconnect the voltage leads from the UUT.
  3.002  DISP
  3.003  DISP         Connect the STANDARD CURRENT TRANSDUCER(clamp) that is
  3.003  DISP         supplied with the UUT, to the POWER MASTER IIIB.
  3.004  DISP         Connect a 5500A/COIL to the 5500A AUX terminals.
  3.004  DISP
  3.004  DISP         Clamp the CURRENT TRANSDUCER around the coil.
  3.005  DISP         Set Function to Amps
  3.006  5500         50.0A          1% 0.1U       60H            SI       T5
  4.001  5500         500A           1% 1U         60H            SI       T5
  5.001  HEAD         {POWER}
  5.002  DISP         Leave the CURRENT TRANSDUCER connected.
  5.002  DISP
  5.002  DISP         Re-connect the voltage leads:
  5.002  DISP         [32] 5500A NORMAL HI to UUT Red Voltage Input
  5.002  DISP         [32] 5500A NORMAL LO to UUT White Voltage Input
  5.003  DISP         Set Function to kWatts
  5.004  M550         100V                                        SI
  5.005  5500         50A                          60H            SI    S  T5
  5.006  ACC          5.00kW         0.0466U
  5.007  MEMI         Enter the UUT Power reading kilowatts.
  5.008  MEME
  5.009  MEMC         5.00kW         0.1U
  6.001  DISP         Set Function to PF%/AVG
  6.002  M550         100V                                        SI
  6.003  5500         5kW                          60H            SI    S  T5
  6.004  ACC          100.0dpf       0.00%
  6.005  MEMI         Enter UUT reading in DPF.
  6.006  MEME
  6.007  MEMC         dpf            0.6%
  7.001  M550         *
  7.002  DISP         Disconnect the 5500A/COIL from the 5500A AUX terminals.
  7.003  HEAD         {PHASE ANGLE}
  7.004  DISP         Connect the 5500A to the UUT as follows:
  7.004  DISP         [32] NORMAL HI to UUT Red Voltage Input
  7.004  DISP         [32] NORMAL HI to UUT Blue Voltage Input
  7.004  DISP         [32] NORMAL LO to UUT White Voltage Input
  7.005  DISP         Set Function to Volts
  7.005  DISP         Set ELEMENT to T/angle
  7.006  5500         60V                          60H            SI    S  2W
  7.007  MEMI         Enter UUT reading in degrees.
  7.008  MATH         MEM1 = MEM - 180
  7.009  JMPT         8.002
  7.010  ACC          0deg           0.15U
  7.011  MEME
  7.012  MEMC         deg            3U
  8.001  JMP          9.001

  8.002  ACC          360deg         0.15U
  8.003  MEME
  8.004  MEMC         deg            -3U
  9.001  END